On 1 December 2026, Australia’s Workplace Exposure Standards (WES) become Workplace Exposure Limits (WEL) — a new national list with tighter limits for dozens of airborne contaminants. The respirable crystalline silica limit is not one of them: it stays at 0.05 mg/m³ (8-hour TWA) after WHS ministers declined to adopt a proposed halving to 0.025 mg/m³ and requested further analysis.

That single sentence answers the question most safety managers are typing into Google right now. But the detail underneath it matters, because “the silica limit isn’t changing” is not the same as “nothing is changing” — and treating 1 December as a non-event would be a mistake for any mining, quarrying or civil operation in Australia.

What changes on 1 December 2026?

From 1 December 2026, Safe Work Australia replaces the WES list — adopted in 1995 and last comprehensively reviewed in 2003 — with the Workplace Exposure Limits for airborne contaminants (WEL) list. The WEL list operates nationally. Until 30 November 2026, the current WES list still applies.

Three things change in practice:

  1. “Standard” becomes “limit” to make the intent unambiguous: these are levels that must not be exceeded, not best-practice recommendations. The wording now aligns with international practice.
  2. Most limits carry over unchanged, but a substantial number have been reduced — some sharply — based on health evidence gathered since 2003 and more than 1,100 public submissions to Safe Work Australia’s review.
  3. Chemicals identified as non-threshold genotoxic carcinogens (NTGCs) no longer carry a numeric limit at all. Because no exposure level can be considered safe, PCBUs must eliminate exposure so far as reasonably practicable, or minimise it through the hierarchy of controls — substitution, isolation, then engineering controls before administrative measures and PPE.

The three types of limit are unchanged in form: the 8-hour time-weighted average (TWA), the 15-minute short-term exposure limit (STEL), and peak limitation. What changes is which numbers sit against which substances — and how seriously the word “limit” signals they will be enforced.

Are environmental regulations, health and safety concerns or potential profit loss a concern right now?

Why is the silica exposure limit staying at 0.05 mg/m³?

Respirable crystalline silica is one of nine chemicals excluded from the new limits — alongside benzene, chlorine, copper, formaldehyde, hydrogen cyanide, hydrogen sulphide, nitrogen dioxide and titanium dioxide.

Safe Work Australia prepared a Decision Regulation Impact Statement analysing the costs and benefits of lower exposure levels for these nine, including halving the silica limit from 0.05 to 0.025 mg/m³. In June 2026, WHS ministers responded: a majority in support of the new levels was not reached, and a majority requested further work. SafeWork SA confirms there will be no changes to the exposure limits for the nine chemicals from 1 December 2026 — they carry across to the WEL list at their current WES levels.

Three points of context stop this being misread as a softening:

  • The limit was already halved once. Silica dropped from 0.1 to 0.05 mg/m³ in 2020, and most sites are still working through what consistent compliance at 0.05 looks like across a full roster.
  • A lower limit is still on the table. Ministers asked for further analysis, not a permanent rejection. Operators who engineer exposure down toward 0.025 now will not be scrambling if the number eventually moves.
  • The silica duties already in force don’t move an inch. The engineered stone ban, and the crystalline silica substance duties that commenced 1 September 2024 — risk assessments, silica risk control plans, air monitoring, health monitoring and training — continue unchanged. The December transition adds to that framework; it does not reset it.

What does change for dust-exposed industries?

While silica holds, other limits relevant to mining, quarrying, tunnelling and civil construction do move on 1 December 2026. The one with the widest reach is diesel particulate matter: DPM receives its first national exposure limit, set at 0.01 mg/m³ (8-hour TWA, measured as respirable elemental carbon). For underground operations running diesel fleets, this lands as a new compliance obligation on the same day the silica status quo is confirmed — and managing diesel particulate and roadway dust in the same ventilation circuit is now a combined engineering problem, not two separate ones.

A number of other substances encountered on industrial sites — including several solvents, metals and gases — also take reduced limits under the WEL list. Safe Work Australia publishes a full comparison in its Changes to Workplace Exposure Limits document; every operator should re-baseline their hazardous chemicals register against it rather than assuming their substances are unaffected.

Dust limits at a glance: what applies from 1 December 2026

Contaminant Limit (8-hr TWA) Change on 1 Dec 2026 Notes for operators
Respirable crystalline silica 0.05 mg/m³ No change — carried to WEL list Proposed 0.025 mg/m³ under further analysis; existing silica duties (since 1 Sep 2024) continue
Respirable coal dust (QLD & NSW coal mines) 1.5 mg/m³ No change Set under state mining legislation (RSHQ in QLD, NSW Resources Regulator), not the national list
Diesel particulate matter 0.01 mg/m³ (as respirable elemental carbon) New — first national limit Biggest single new obligation for underground diesel fleets
Nuisance dust guidance (dusts not otherwise classified) 10 mg/m³ inhalable Guidance position Not appropriate where the dust contains silica or other toxic constituents

Two compliance realities sit behind this table. First, mining-specific limits like respirable coal dust are enforced by state mine safety regulators under their own legislation, so the national WES-to-WEL transition does not alter them. Second, Safe Work Australia is explicit that an exposure limit is not the line between a safe and unsafe workplace — the duty is to keep exposure as low as reasonably practicable, and limits in each state take effect as that jurisdiction’s WHS laws adopt them.

How should operators prepare before 1 December 2026?

  1. Re-baseline your hazardous chemicals register against Safe Work Australia’s comparison document. Flag every substance on site whose limit falls, rises, or disappears into the NTGC category.
  2. Check your monitoring data against the new numbers, not the old ones. An operation comfortably under a current WES may sit above its incoming WEL. Diesel particulate is the obvious candidate on underground sites.
  3. Update exposure control plans and SWMS references. Documents that cite “workplace exposure standards” or the superseded values should reference the WEL list from 1 December.
  4. Don’t defer silica work because the limit held. Air monitoring records trending near 0.05 mg/m³ offer no headroom for a bad shift — and the 0.025 proposal remains live.
  5. Brief contractors and labour hire. PCBU duties extend to everyone on site, and the terminology change will surface in audits, tenders and prequalification questionnaires almost immediately.
  6. Confirm when your state adopts the changes. The list applies in each jurisdiction according to how its WHS laws reference it — check your regulator’s guidance rather than assuming a uniform start date.

Why engineering controls decide compliance — not the limit itself

Under the hierarchy of controls, respirators are the last line of defence, not a compliance strategy. Where silica-bearing dust cannot be eliminated, the WHS framework expects engineering controls that stop dust becoming airborne in the first place — and that is where the gap between sites that pass air monitoring and sites that don’t is actually created.

For the activities that generate most respirable silica on mining and civil sites, suppression at the source is a mature, measurable engineering control:

  • Drilling and blasting — capturing dust at the drill collar and binding cuttings piles prevents the finest, most respirable fractions becoming airborne. This is the application GRT: 12X and GRT: DC Binder were engineered for.
  • Underground mining and tunnelling — treating roadways, bolting and cutting faces with suppression agents such as GRT: Activate UG reduces the respirable dust load the ventilation circuit has to dilute, which also matters more once diesel particulate carries its own limit in the same air.
  • Haul roads and trafficked areas — polymer-treated watering with GRT: Haul-Loc keeps fine particles bound into the road surface instead of in the air column, while cutting the water volume required.
  • Exposed areas and stockpiles — surface binders such as GRT: Soil-Loc and GRT: Enviro-Binder crust open areas so wind erosion doesn’t feed background dust levels across the site boundary.

The common thread: every milligram of dust suppressed at the source is a milligram that never reaches a worker’s breathing zone, never shows up in a monitoring result, and never has to be defended to a regulator. With exposure limits now framed as lines that must not be crossed, source control is the cheapest insurance an operation can buy.

Frequently asked questions

Is the silica exposure limit changing in December 2026? No. Respirable crystalline silica stays at 0.05 mg/m³ (8-hour TWA) when the WEL list takes effect on 1 December 2026. A proposed reduction to 0.025 mg/m³ was not agreed by WHS ministers in June 2026 and remains under further analysis.

What is the difference between a WES and a WEL? The numbers work the same way — 8-hour TWA, STEL and peak limitation. The change from “standard” to “limit” makes explicit that these are levels which must not be exceeded, aligning Australia’s terminology with international practice.

Which nine chemicals are keeping their current limits? Benzene, chlorine, copper, formaldehyde, hydrogen cyanide, hydrogen sulphide, nitrogen dioxide, respirable crystalline silica and titanium dioxide. Ministers requested further work before deciding on lower levels for these.

Does the December change affect existing silica duties? No. The engineered stone ban and the crystalline silica substance duties in force since 1 September 2024 — risk assessments, silica risk control plans, air monitoring, health monitoring and training — continue unchanged.

What is the new diesel particulate matter limit? From 1 December 2026, DPM carries its first national exposure limit: 0.01 mg/m³ as an 8-hour TWA, measured as respirable elemental carbon. It most affects underground operations running diesel fleets.

Who enforces dust limits on Australian mine sites? State mine safety regulators — Resources Safety & Health Queensland, the NSW Resources Regulator, and WA’s DEMIRS among them — enforce mining-specific limits such as respirable coal dust under their own legislation, alongside the national list adopted through WHS laws.

Sources


Troy Adams
Troy Adams

Troy Adams is the Managing Director of Global Road Technology (GRT) Specialising in Engineered Solutions for Dust Suppression, Erosion Control, Soil Stabilisation and Water Management. A pioneering, socially conscious Australian entrepreneur, Troy Adams is passionate about health and safety and providing innovative solutions that are cost-effective to the mining industry, governments and infrastructure sectors. Troy is also a tech investor, director of companies like Crossware, Boost, Hakkasan, Novikov and more.

Subscribe for Email Updates

To get more news and updates like this directly to your inbox, subscribe to our monthly newsletter.